most recent revision of the AAMA and. field testing protocols. AAMA 08,. “Voluntary Specification for Field Testing of. Newly Installed Fenestration. The AAMA (Voluntary Specification for Field Testing of Newly Installed Fenestration Products) is a field-testing guide developed by the American. AAMA Voluntary Specification for field testing of newly installed fenestration products. Includes Air Infiltration and Water Penetration.
|Published (Last):||25 June 2013|
|PDF File Size:||1.33 Mb|
|ePub File Size:||1.33 Mb|
|Price:||Free* [*Free Regsitration Required]|
Have flashing and sealing been properly finished? Normally, if a window fails, the contractor should be prepared for a wider scope of testing.
Our field consultants are properly trained and knowledgeable of all testing standards. See our AAMA page for additional information.
AAMA Test Standard for Air & Water Infiltration
The AAMA can be utilized if the project requires investigative 502-0. It is up to the contractor to ensure these testing parameters are established. This field check procedure is only intended to evaluate joints, gaskets and sealant details in the glazing which are designed to remain permanently closed and water tight. The most current edition is the AAMA One-week notice prior to water testing is usually given to aqma construction crew members concerned with window installation.
It is not recommended to notify anyone of the actual test locations until the testing agency arrives onsite.
AAMA Water Spray Testing
What is the drainage design? Search by product code or category or leave the product code field blank to see a list of all AAMA publications. Field testing and forensic leak investigation services are provided nationwide. This guideline is for forensic or investigative water spray testing only.
If you are looking for a reputable second or third-party testing company to perform accurate professional testing, provide concise reports, and help you through the entire process, contact BDG today.
The project architect, manager, or owner specifies the amount and locations of the windows to be tested; this happens either early in the project or at three intervals in the case of large projects: Are the edges perfectly horizontal and vertical? Member discount will be reflected after successful login to the Checkout process.
AAMA Water Spray Testing
How is the installation quality? For window and door manufacturers, the procedure provides a uniform approach for dealing with different code jurisdictions and specific design pressure for each size of fenestration 50208 opening. Begin your publication search by entering information into the fields below. A predetermined amount of air leakage is allowable; however, no water leakage is permitted at all. With a large project, testing early on can prevent expensive repairs if a design flaw is identified during the first phase of testing.
These specifications establish the requirements for field test specimens, apparatus, sampling, test procedures and test reports to be used in verifying the air infiltration resistance performance and water penetration resistance performance of installed new windows and sliding glass doors hereafter referred to as “fenestration products”.
Then both air and water leakage aams that order are determined using a test chamber of constant pressure. Guidelines for the type of equipment to use and test procedures to follow are specified in the AAMA Testing shall be performed by an AAMA accredited independent testing agency. Read more about what our customers have to say There are no previous editions. This specification is for quality assurance water penetration testing only.
Please contact AAMA for assistance, as needed. 052-08 testing, the window installation is visually observed. This allows us to not only properly test fenestrations on new construction projects, but also pinpoint the cause of any test failures and provide accurate recommendations to achieve successful testing results. The construction contract will appoint a party responsible for the cost of the testing. Give us a call to discuss your next project.
If the window installation was completed within 6 months, and there is not a building occupancy permit COthen the AAMA is the right document to use. The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage and water penetration resistance performance. Is the window square? It’s important to note that the Aam test standard also utilizes the ASTM E test method which details specific test set-up and equipment requirements for the water penetration portion of the test, and the ASTM E test method which details test set-up and equipment requirements for the Air Infiltration portion of the test.
What are FTL’s Qualifications? See our AAMA page for additional information if your project requires to test for the rated air leakage or rated water penetration performance. It is primarily used for new construction quality control and assurance purposes.
The AAMA was first released in and has had many changes over the years. American Architectural Manufacturers Association.
aamma Any moisture not coming in through the window, but getting in somehow, will be subject to further forensic investigation. This specification establishes the requirements for field test specimens, apparatus, sampling, test procedures and test reports to be used in verifying the air infiltration resistance performance and water penetration resistance performance of newly installed fenestration products. SITC utilizes isolation techniques to assist in identifying the source or sources of the reported water leakage.
A specified pressure is maintained while any escaping air is measured. MISSION Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset. This field check is not appropriate for testing operable components.
BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results. Water leakage uses the same method while spraying the window from outside to observe indoor penetration. Typically, a sampling of windows from the project is selected and tested.