The compact DISOMAT® Tersus weighing terminal is ideal for use in a wide range of weighing applications, regardless of whether you’re focusing on operating. DISOMAT® Tersus to control a crane DISOMAT® Tersus panel-mounting unit in field housing DISOMAT® Tersus Crane Scale, see Manual BV-HAA. A Schenck model DISOMAT Tersus (VTG ) digital indicator as shown in between weighing ranges may be automatic or manual.
|Published (Last):||15 March 2016|
|PDF File Size:||14.41 Mb|
|ePub File Size:||18.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Interfaces Connectors Figure To do so, set jumpers W and W to position B01 and user cable V Secondary Tsrsus Connectors 5. For details, please see technical data of individual bus system. If the application requires more than one serial interface, interface expansion VSS can be employed.
The module is organized as ring buffer, i. In the safe area, the sealing ring may be exchanged; certified screwed connections must be replaced in set.
With this type of circuitry, voltage is available across inputs with open switch logical LOW signaland check LEDs light. Local Box VVG 4. Base Unit Figure 7: To replace, remove barrier from carrier module. Measure voltage using a suitable instrument e.
All in all, these features save time and money. Safety Instructions Use As Originally Intended The measuring system and its connected mechanical components are exclusively designed for weighing and controlling tasks. E unit is at least 12V. DXB Mechanical dimensions of equipment used: Width [mm] 73 10 6 24 40 30 Height [mm] 99 99 35 48 48 90 78? Ensure that any repair work affecting the explosion protection is performed by a skilled electrician in accordance with local regulations.
When mounting the explosion-proof protective circuitries complete with connecting parts, ensure that protection to at least IP20 is reached. The PC board is equipped with two bus connectors.
Do not use any external circuitry to invert this logic; this would affect wire-break safety and disable further processing of signals in DISOMAT.
In addition, the load cells signals can be recorded individually. Connection takes place across connector XE1 using a standard network cable with plug RJ The following search criteria are possible: Assemble parts of the dongle plastic housing using clips.
For itemssee Fig.
For wiring diagrams, see pages to follow. RS and RS can be used as alternative only 1 physical interface. Schedule an appointment with us whenever you need it.
This offers an attractive solution for remote control even via modem. For connection of secondary displays, see wiring diagram page Best use new hex tesus from the bus board kit in place of the recessed head screws.
The firmware and all individual set parameters are backed up and restored in next to no time. Explosion-proof Protective Circuitries Fig.
Secondary Displays You can connect various secondary displays for different mounting sites e.
Desk-top Housing VTG Subject to change without prior notice. For details, see manual BV-H The latter can be accessed after removal of the easily accessible CPU and etrsus circuit boards remove coupling board, if present. B01 mmor V Before performing work on the electrical equipment, disconnect the power supply.
Maintain jumper position on all other devices.
System Manual DISOMAT_百度文库
If other makes are used, the warranty will be void. The passive bus connection can then be omitted. Error Message Acknowledgement Error messages may be acknowledged only after cause of fault has been remedied.
The supervisor is responsible for instructing his operators to observe all regulations and instructions given. Remount clamping nut and tighten. B01 Maximum safety distance: In the case of load cell supply, this value depends on the total impedance and thus on the number of load cells. To ensure optimal EMC resistance, we recommend to use the cables indicated for the single fieldbuses. Maintenance and Repair During maintenance and repair, observe any warning symbols on the scale.
For details, see Operating Manual, Item 5. Interfaces The following interfaces are available: The system identifies a missing memory module automatically and outputs an error message upon the next storage attempt. A fieldbox with a disokat degree of protection is available. It is compatible with the previous version and also offers a range of noteworthy optimisations for ambitious planning.