FTR USB UART IC Datasheet Version Clearance No.: FTDI# •. •. Neither the whole nor any part of the information contained in, or the product. FTDI FTRL: available from 8 distributors. Explore Integrated Circuits ( ICs) on Octopart: the fastest source for datasheets, pricing, specs and. FTRL Datasheet, FT FTDI USB to Serial UART IC Datasheet, buy FTRL USB to Serial UART IC.
|Published (Last):||11 August 2006|
|PDF File Size:||11.64 Mb|
|ePub File Size:||12.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
When a non -standard baud rate is required simply pass the required baud rate value to the driver as normal, and the FTDI driver will calculate the required divisor, and set the baud rate.
In accordance with the USB 2. A useful feature of these devices is the SHDN pin which can be used to power down the device to a low quiescent current during USB suspend mode. This package is datasheeg 5. Preheat – Temperature Min T s Min. A suitable power switch IC for such an application is the Micrel www. A suitable range of Ferrite Beads is available from Steward www.
If this is not possible, use the configuration shown in Section 6. The solder pads are on a 0. Corrected Tape and Reel quantities. FTDI 38 Table 5. The pins are on a 0. These characteristics only apply when an external oscillator or crystal is used.
Single chip USB to asynchronous serial data transfer interface. USB bulk transfer mode.
FTR Datasheet(PDF) – Future Technology Devices International Ltd.
When data is being transmitted or received the respective pins will drive from tri-state to low in order to provide indication on the LEDs of data transfer. New CBUS bit bang mode option. For details on how to use an external crystal, ceramic ft22r, or oscillator with the FTR, please refer Section 7. This is followed by the revision number.
FT232RL USB to UART Breakout Board
Sys tem and equipment manufacturers and des igners are responsible to ens ure that their s ystems, and any Futu re T echnology D evic es I nternational L td FTDI devices incorporated in their s ys temsmeet all applic able s afety, regulatory and s ys tem – level performanc e requirements. The solder reflow profile for both packages is described in Section 9.
This mode differs from asynchronous bit bang mode in that the interface pins are only read when the device is written to. This gives achievable baud rates in the range Auto transmit buffer control for RS applications.
Exceeding these may cause permanent damage to the device.
FTR USB UART IC Datasheet | Kevin Zaat –
The FTR adds two new functions compared with its predecessors, effectively making it a “3-in-1” chip for some application areas. Tx relative to the USB interface. The FT-X series is the ft223r device family offering reduced power and pin count with additional features such as battery charge detection, while the Hi-Speed solution offers faster interfacing. Adjustable receive buffer timeout. The centre pad on the base of the FTRQ is not internally connected, and can be left unconnected, or connected to ground recommended.
The SP is specified to transmit and receive data at a rate of up to 5 Mbaud. N eith er the whole nor any part of datasheeet information c datawheet in, or the produc t d es cribed in this document, may be adapted or reproduc ed in any material or elec tronic form without the prior written c ons ent of the c opyright holder. T his product or any variant of it is not intended for us e in any medic al appli anc e, devic e or s ys tem in whic h the failure of the produc t might reas onably be expec ted to res ult in pers onal injury.
N o freedom to us e patents or other intellectual property rights is implied by the public ation of this doc ument. This is a common feature of RS and requires the application software to remove the transmitted data from the received data stream.
In-built support for event characters and line break condition.