Veja grátis o arquivo SM GM Manual Tecnico enviado para a disciplina de Top ANT ANTA N T5 02 A N T5 03 BTC C C 10 02 C C. SERVICE MANUAL / # X / 10/ AKG CUSTOMER SERVICE DEPARTMENT / Laxenburger aus dem Gehäuse schieben. 1. C S MKIV. Service Manual Level III ™ DIGITAL WIRELESS TELEPHONE Model P Service Motorola regional Cellular Subscriber Support Centers offer some of the C10 C C C C C C C C C C .
|Published (Last):||9 March 2016|
|PDF File Size:||12.77 Mb|
|ePub File Size:||20.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
The resultant bits are sent to a data converter to be modulated. The voice path is unmuted. However, TDMA also compresses the digitized signal, making use of predictive algorithms to reduce the number of symbols actually transmitted. There are two types of multiplexing that are feasible for cellular: Call Config Screen Set Amplitude to: Traffic Chan should be set to In conventional analog radio, speech is converted into varying voltages called manuap by celhlar microphone.
But one thing remained constant, there were 21 control channels for each carrier. As the temperature increases the thermistor will decrease in resistance, causing the supply level at the thermistor to decrease.
The mobile measures the RSSI of neighboring channels, as instructed by the base station. Access channels are used to respond to a page or originate a call. Using the pointed end of the plastic prying tool, insert it on the right side of the locking tab.
Number assigned by system operator for system identification. User 10 digit radiotelephone phone number.
With this in consideration, U will also have only to possible states. Instantaneous samples are discrete voltages.
SM G360M Manual Tecnico
U11 also has some internal buffers for the receive signals and the VCO signals. Service Manual Cellular Overview Digital Cellular voice samples as viewed on oscilloscopes, are clearly shown to be nothing more than varying voltages produced by microphones. The following page describes the step by step procedure for Easy NAM Programming, which is the preferred programming method.
Put the Test Set in Active state by selecting Active from the list on the left side of the screen. The cell sites are in communication with individual portable and mobile cellular telephones.
Remove the radio fixture and remove the housing. Therefore, it is important that you test the RF cable for proper loss.
This block also contains filtering to remove aliases before sampling. Preferred System Bit A6. mznual
AKG CS MKII Service Manual download, schematics, eeprom, repair info for electronics experts
Secondary Initial B system channel. And, of course, in digital cellular, all signaling is digital. Auxiliary Alert Bit A2. In order to turn off the NoSvc light, the overhead message stream must have been decoded.
The RSSI signal has a filtering capacitance that changes with respect to the operating mode e. An anti-static wrist band, connected to an anti-static conductive work surface, must be worn during all phases of manuaal, repair, and reassembly.
A4 Custom IC U Under the ,anual AMPS protocol there were 21 control channels assigned to each of two possible carriers in any metropolitan area, with a total of channels assigned to each carrier. The carrier is then passed through an IQ modulator. In this level of manual test mode the phone will place and receive calls as normal, but the display shows two lines of status information. Place backhousing on phone making sure side snaps clip the backhousing and push forward snapping everything back in place.
Enhanced Scan Enable Bit D7. Slip the tweezers between front housing and battery contacts. Having a low state at the output of U will invert all the states. User Mode Programming User Mode NAM programming requires a special key sequence to enter, but can be accomplished through the telephone keypad without the use of any specialized hardware. Vibrator On Off J 1. The 7th-order odd polynomial minimizes the amount of spectral splatter and is realized in software.
All of these non-voice signals are digital and take time from the assigned time slot, leaving only a relatively small amount of time to represent voice. The switch then connects the mabual call to the appropriate circuit leading to the cell in contact with the cellular telephone.
Do not confuse data with the 10 kHz signaling tone. Once the main battery is fully manuak, it will begin charging the auxiliary battery. The telephone powers up and runs a self-test.
There are 3 significant bits for the secondary initial paging channel. Audio adjust amplifier is realized in software. A 2 digit number assigned by the system operator. celulaf
Light sleep – Clocks running, but lower power consumption 3. The frequency is controlled by U Exits the programming mode without programming the NAM.